PIRA Code(s): 5A20.20 Set up time:1 minute Operation: Charge the rod by rubbing it the through the cloth provide or on your shirt. Hold the rod near a pith ball. The two balls will repel each other. The PVC gives a positive charge and the acrylic rod gives negative charge. Physics and Science Concepts: Electrostatics, Coulomb’s Law Safety: None
PIRA Code(s): 5A50.10 Set up time:2 minutes Operation: Place the four (two large, two small) balls on the poles in the front about 1 inch apart. Turn the crank. Physics and Science Concepts: Electrostatics Safety: Do not touch any metal portions of the generator
PIRA Code(s): 5B30.20 Set up time:5 minutes Operation: Use the Van der Graaf or Wimshurst generator to charge the ovoid. Touch a proof plane to the pointed end of the ovoid and another to the spherical end. Place the proof planes on the electroscope plate. The deflection will be greater from the proof plane that touched the pointed end. Physics and Science Concepts: Electrostatics, Surface Charge Density Safety: Electroscope can be obtained from demonstration number 5A22.22.
PIRA Code(s): 5C10.20 Set up time:none Operation: Charge the plates using the Van de Graaff. Disconnect wire going from top of sphere to fixed plate at plate end. Change the spacing of a charged parallel plate capacitor while it is attached to an electroscope. Observe changes in electroscope pointer. Physics and Science Concepts: Capacitance Safety: Electroscope can be obtained from demo 5A22.22. The Van de Graaff can be obtained from demo 5A50.30.
PIRA Code(s): 5E40.20 Set up time:1 minute Operation: Pour sulfuric acid into the glass container. Wait 5 minutes for the reaction to take place between the dissimilar metals. Place the voltmeter on the overhead and display the voltage generated in the cell. Physics and Science Concepts: Electromotive Force and Current Safety: Be careful around acid. Gloves and goggles should be worn when handling acid.
PIRA Code(s): 5F20.50 Set up time:5 minutes Operation: First, attach the metal rods to the battery by unscrewing the black caps and place the rods around the screws. Then replace the caps. Next, clip one light bulb on the metal rods to show a circuit with a single light bulb. To show series circuits, clip two bulbs together and place the end of each clip on opposite rods. To show parallel circuits, clip each bulb separately to the rods. The bulbs in series will glow less brightly than the bulbs in parallel. Physics and Science Concepts: Parallel and series circuits Safety: The ends of the rods pose an eye hazard.
PIRA Code(s): 5G50.50 Set up time:2 minutes Operation: A superconductor disc is placed in a styrofoam dish and liquid nitrogen is added to the dish. A small magnet is placed on top and within a few seconds it begins to levitate. Physics and Science Concepts: Superconductivity, Magnetic Materials Safety: Liquid Nitrogen can be obtained from the machine shop.
PIRA Code(s): 5H30.10 Set up time:2 minutes Operation: Plug in the cathode ray tube. Deflect the beam of the CRT by holding a permanent magnet near the edge of the tube. If the beam disappears, you are holding the magnet too close. Also, you can deflect the beam by attaching a battery to the binding posts and adjusting the variable control knob. Physics and Science Concepts: Magnetic Fields and Forces Safety: None
PIRA Code(s): 5K10.20 Set up time:1 minute Operation: Hook the leads from the galvanometer to the induction coil. Place a magnet in front of the coil. Turn the crank and the needle on the galvanometer should move. The connection between the galvanometer and the loop changes polarity every half turn. Physics and Science Concepts: Electromagnetic Induction, Electricity and Magnetism Safety: Magnet is extremely strong so do not place metal objects near it.
PIRA Code(s): 5K20.10 Set up time:5 minutes Operation: Set up the pole with the right angle clamp and pendulum. Place the permanent magnet so that the copper sheet is in between the two magnet sides. Swing the full copper sheet swing through the magnet. Watch as it damps out quickly. The, flip the pendulum so that the copper comb side is swinging through the magnet. Watch how it swings as if the magnet is not even there. Physics and Science Concepts: Electromagnetic Induction, Eddy Currents Safety: Stand to the side of the pendulum as it swings, not directly in the path.
PIRA Code(s): 5L20.14 Set up time:1 minute Operation: Plug in the circuit. Flip the switch that says line and then put the lever to the automatic side for the whole lamp to light up. Flip the line switch again and move the lever to the middle. Put the line switch on again and move the lever to the manual side. This will heat up the filament. Then move the lever a little away from the manual side for the entire light to be lit. Physics and Science Concepts: AC Circuits Safety: None