PIRA Code(s): 3A10.40 Set up time:none Operation: Push the pendulum so that it swings back and forth at an angle of about 0 º. Then, slowly increase the angle, and watch the frequency decrease. For a more effective demonstration, start the pendulum at a relatively high angle, and then decrease the angle of the plane of oscillation so that the frequency of the pendulum will increase over time. Physics and Science Concepts: Oscillations Safety: None
PIRA Code(s): 3B30.30 Set up time:10 minutes (5 minutes to pump the bell jar) Operation: Plug in the pump and attach the clear tube of the pump to the valve. Turn the switch on the power supply to ascertain that the alarm is working properly. Then, pump out the air inside the bell jar. It will take about 5 minutes to obtain a low enough air pressure so that the alarm will not sound. Turn the alarm on and slowly open the valve, allowing the air pressure in the bell jar to increase. The sound of the alarm will also gradually increase. Physics and Science Concepts: Sound waves Safety: A glass jar containing a vacuum can be extremely hazardous if broken.
PIRA Code(s): 4A30.10 Set up time:1 minute Operation: Use a Bunsen burner to heat a bimetal strip and it will bend Physics and Science Concepts: Thermodynamics, Thermal Properties of Matter, Thermal Expansion Safety: Use caution when dealing with the Bunsen burner. Bunsen burner not included.
PIRA Code(s): 4C33.50 Set up time:No setup required Operation: Hold one bulb in your hand so that it forces the liquid to enter the other bulb. Physics and Science Concepts: Change of State, Vapor Pressure Safety: Do not grasp too tightly as the glass may break.
PIRA Code(s): 4E30.10 Set up time:5 minutes Operation: Fill sphere with water and submerge in buckets of water or liquid nitrogen at different temperatures. Dewar of liquid nitrogen and bucket can be obtained in the physics machine shop. Physics and Science Concepts: Gas Laws, Thermodynamics Safety: Always wear protective clothing when handling liquid nitrogen.
PIRA Code(s): 5A50.10 Set up time:2 minutes Operation: Place the four (two large, two small) balls on the poles in the front about 1 inch apart. Turn the crank. Physics and Science Concepts: Electrostatics Safety: Do not touch any metal portions of the generator
PIRA Code(s): 5A50.30 Set up time:10 minutes Operation: Plug in the generator. Turn on the rocker switch and adjust speed using potentiometer on the base of the Van de Graaff.
Other suggested uses include combining this with other electrostatic demonstrations found under a 5A50 heading. Also, throwing packing peanuts or taping strips of paper to the Van de Graaff are popular demonstrations. Physics and Science Concepts: Static Electricity, Friction Safety: The rod works best on dry days with the blue wig. Care should be taken when operating. Do not approach the generator while it is running. Use the grounding rod to discharge.
PIRA Code(s): 5C30.40 Set up time:5 minutes Operation: Jars can be charged with either the Wimshurst generator (5A50.10) or Van de Graaf generator (5A50.30). Charge Leyden jars in parallel and discharge, charge in parallel again and connect in series before discharging. The intensity of the sparks as well as their duration is much greater for the series connection. Physics and Science Concepts: Electricity and Magnetism, Capacitance Safety: Do not touch the charged capacitor. Make sure the jar is discharged before storing or touching.
PIRA Code(s): 5F20.50 Set up time:5 minutes Operation: First, attach the metal rods to the battery by unscrewing the black caps and place the rods around the screws. Then replace the caps. Next, clip one light bulb on the metal rods to show a circuit with a single light bulb. To show series circuits, clip two bulbs together and place the end of each clip on opposite rods. To show parallel circuits, clip each bulb separately to the rods. The bulbs in series will glow less brightly than the bulbs in parallel. Physics and Science Concepts: Parallel and series circuits Safety: The ends of the rods pose an eye hazard.
PIRA Code(s): 5G50.50 Set up time:2 minutes Operation: A superconductor disc is placed in a styrofoam dish and liquid nitrogen is added to the dish. A small magnet is placed on top and within a few seconds it begins to levitate. Physics and Science Concepts: Superconductivity, Magnetic Materials Safety: Liquid Nitrogen can be obtained from the machine shop.
PIRA Code(s): 5H10.30 Set up time:3 minutes Operation: Place the magnet under the piece of paper and on the overhead. Sprinkle iron filings over the magnet and the filings should align with the magnetic field. Physics and Science Concepts: Magnetic Fields and Forces Safety: An overhead can be obtained from demonstration 9A36.10.
PIRA Code(s): 5H30.10 Set up time:2 minutes Operation: Plug in the cathode ray tube. Deflect the beam of the CRT by holding a permanent magnet near the edge of the tube. If the beam disappears, you are holding the magnet too close. Also, you can deflect the beam by attaching a battery to the binding posts and adjusting the variable control knob. Physics and Science Concepts: Magnetic Fields and Forces Safety: None
PIRA Code(s): 5K20.10 Set up time:5 minutes Operation: Set up the pole with the right angle clamp and pendulum. Place the permanent magnet so that the copper sheet is in between the two magnet sides. Swing the full copper sheet swing through the magnet. Watch as it damps out quickly. The, flip the pendulum so that the copper comb side is swinging through the magnet. Watch how it swings as if the magnet is not even there. Physics and Science Concepts: Electromagnetic Induction, Eddy Currents Safety: Stand to the side of the pendulum as it swings, not directly in the path.
PIRA Code(s): 5K20.30 Set up time:2 minutes Operation: Set up the apparatus so that the silver pole sticks above the platform a few inches. Place a full ring around the tube and turn the apparatus on. This will make the ring jump into the air. Turn off the machine then, place the split ring around the pole, turn on the machine and this will not do anything. Resistive heating can be demonstrated by holding the full rings down and feeling them heat up. Next, turn off the machine, place the copper coil around the pole and press down on the copper rod sticking off the coil to create sparks. Also, place the light bulb circuit ring against the flat top part of the pole and watch it light up. Physics and Science Concepts: Lenz law, Electromagnetic Induction, Eddy Currents Safety: Do not place apparatus directly under a light. Do not stand above machine when the rings jump. Do not hold the full ring down too long, you may get burned.