PIRA Code(s): 1D60.30 Set up time:10 minutes Operation: Set up two ring stands about 8 feet apart. Put the blow gun in the clamp on one stand with the power cords to the inside of the set up. Attach the pole with the magnet to the other ring stand. Place the ball into the blow gun. Switch the power supply on which connects the circuit and then place the monkey (band aid box) on to the magnet, upside down. Make sure the blow gun is aimed directly at the broad side of the monkey. Now, blow into the blow gun to release the ball and break the circuit, thus causing the monkey to fall. The ball should hit the monkey as it falls. Physics and Science Concepts: Projectile Motion, Gravity, and Mechanics Safety: Do not turn power supply on before inserting the ball into the blow gun, due to possible electrocution.
Not all pieces (ring stand, 5 V ½ Amp DC power supply, and clamps) are in the kit, these items need to be acquired.
PIRA Code(s): 1L20.40 Set up time:5 minutes Operation: Remove pieces from the cone to show different conic sections. Physics and Science Concepts: Gravity Safety: Nails that connect pieces may be sharp.
PIRA Code(s): 1M20.30 Set up time:5 minutes Operation: Set the empty friction box on the incline with weights attached to the string on the other side of the pulley so that the box slides forward. Then, gradually increase the angle of the plane until the box and the weights reach equilibrium. Physics and Science Concepts: Equilibrium of forces, Mechanics, Work and Energy Safety: None
PIRA Code(s): 1Q40.23 Set up time:1 minute Operation: Place the shaft of the device into the hole and tighten the screw. Then, plug in the motor and turn on the red switch. When spun, the hoops will show oblation, the balls on the governor will move outwards, and the liquid in the glass sphere will move to the edge of the sphere. Physics and Science Concepts: Rotational Dynamics, Centrifugal Force, Oblation Safety: Wear goggles when running the apparatus and keep hands away from the belt.
PIRA Code(s): 1Q40.30, 1Q50.24 Set up time:3 minutes Operation: Stand on the stool as it remains still. Have someone start the motor and place the bicycle wheel next to it to get it to start spinning. Take the spinning wheel in your hands and turn the wheel in a horizontal position and you should spin. When the wheel is placed vertical again, you will spin the opposite direction.
Use the motor to start the wheel spinning. Hold on to the cord attached to the axle and the wheel will remain vertical. Physics and Science Concepts: Mechanics, Rotational Dynamics Safety: Do not get items caught in the motor or the spokes of the tire. Hold wheel out from the body as far as possible
PIRA Code(s): 1Q40.40 Set up time:5 minutes Operation: Place the train on the track. Plug the track into the variac and start the train by moving the dial. Physics and Science Concepts: Mechanics, Angular Momentum, Rotational Dynamics, Angular Momentum, Relative Motion Safety: Watch for sparks from the train. Maintain a cautious distance from the wheel.
PIRA Code(s): 1Q40.42 Set up time:1 minute Operation: Instructions included in box. Must obtain ring stand and clamp from 9C40.71 and 9C40.72, respectively. A known weight attached to a string around the wheel torques the wheel a constant amount. Physics and Science Concepts: Moment of Inertia, Mechanics Safety: Use caution around spinning wheel.
PIRA Code(s): 1Q40.80 Set up time:5 minutes Operation: Partially fill flask with water. Attach flask by string to ring stand. Then, use a Bunsen burner or a torch to heat the flask. The flask should rotate as the steam emerges from the arm. Physics and Science Concepts: Rotational Dynamics, Conservation of Angular Momentum, Safety: Use caution around Bunsen burner or torch. Do not overheat the glass as it may shatter. Eye protection should be worn. The torch can be acquired from the machine shop if necessary.
PIRA Code(s): 1Q50.30 Set up time:1 minute Operation: Rotational Dynamics, Mechanics, Gyroscopic Motion Physics and Science Concepts: Rotational Dynamics, Mechanics, Gyroscopic Motion Safety: The central gyroscope is quite heavy and can pinch fingers.
PIRA Code(s): 1Q50.60 Set up time:2 minutes Operation: Use the string or turn the rotor with your thumb to start the gyroscope spinning. Take care to hold the gyroscope and metal hold in place relative to the top block of wood. Then, spin the wooden block, stop it, and reverse the direction of the spin. The gyroscope will do a spin flip. Physics and Science Concepts: Rotational dynamics, Mechanics Safety: None
PIRA Code(s): 2B30.30 Set up time:3 minutes Operation: Place the two halves together. Put the vacuum pump on the valve and evacuate the air inside. Try to separate the pieces. Vacuum pump not included; it must be obtained from demo 3B30.30. Physics and Science Concepts: Fluid Mechanics, Statics of Fluids Safety: None
PIRA Code(s): 3A10.40 Set up time:none Operation: Push the pendulum so that it swings back and forth at an angle of about 0 º. Then, slowly increase the angle, and watch the frequency decrease. For a more effective demonstration, start the pendulum at a relatively high angle, and then decrease the angle of the plane of oscillation so that the frequency of the pendulum will increase over time. Physics and Science Concepts: Oscillations Safety: None
PIRA Code(s): 3B30.30 Set up time:10 minutes (5 minutes to pump the bell jar) Operation: Plug in the pump and attach the clear tube of the pump to the valve. Turn the switch on the power supply to ascertain that the alarm is working properly. Then, pump out the air inside the bell jar. It will take about 5 minutes to obtain a low enough air pressure so that the alarm will not sound. Turn the alarm on and slowly open the valve, allowing the air pressure in the bell jar to increase. The sound of the alarm will also gradually increase. Physics and Science Concepts: Sound waves Safety: A glass jar containing a vacuum can be extremely hazardous if broken.
PIRA Code(s): 4C33.50 Set up time:No setup required Operation: Hold one bulb in your hand so that it forces the liquid to enter the other bulb. Physics and Science Concepts: Change of State, Vapor Pressure Safety: Do not grasp too tightly as the glass may break.
PIRA Code(s): 5A50.30 Set up time:10 minutes Operation: Plug in the generator. Turn on the rocker switch and adjust speed using potentiometer on the base of the Van de Graaff.
Other suggested uses include combining this with other electrostatic demonstrations found under a 5A50 heading. Also, throwing packing peanuts or taping strips of paper to the Van de Graaff are popular demonstrations. Physics and Science Concepts: Static Electricity, Friction Safety: The rod works best on dry days with the blue wig. Care should be taken when operating. Do not approach the generator while it is running. Use the grounding rod to discharge.
PIRA Code(s): 5C30.40 Set up time:5 minutes Operation: Jars can be charged with either the Wimshurst generator (5A50.10) or Van de Graaf generator (5A50.30). Charge Leyden jars in parallel and discharge, charge in parallel again and connect in series before discharging. The intensity of the sparks as well as their duration is much greater for the series connection. Physics and Science Concepts: Electricity and Magnetism, Capacitance Safety: Do not touch the charged capacitor. Make sure the jar is discharged before storing or touching.
PIRA Code(s): 5F20.50 Set up time:5 minutes Operation: First, attach the metal rods to the battery by unscrewing the black caps and place the rods around the screws. Then replace the caps. Next, clip one light bulb on the metal rods to show a circuit with a single light bulb. To show series circuits, clip two bulbs together and place the end of each clip on opposite rods. To show parallel circuits, clip each bulb separately to the rods. The bulbs in series will glow less brightly than the bulbs in parallel. Physics and Science Concepts: Parallel and series circuits Safety: The ends of the rods pose an eye hazard.
PIRA Code(s): 5G50.50 Set up time:2 minutes Operation: A superconductor disc is placed in a styrofoam dish and liquid nitrogen is added to the dish. A small magnet is placed on top and within a few seconds it begins to levitate. Physics and Science Concepts: Superconductivity, Magnetic Materials Safety: Liquid Nitrogen can be obtained from the machine shop.
PIRA Code(s): 5H10.30 Set up time:3 minutes Operation: Place the magnet under the piece of paper and on the overhead. Sprinkle iron filings over the magnet and the filings should align with the magnetic field. Physics and Science Concepts: Magnetic Fields and Forces Safety: An overhead can be obtained from demonstration 9A36.10.
PIRA Code(s): 5K20.30 Set up time:2 minutes Operation: Set up the apparatus so that the silver pole sticks above the platform a few inches. Place a full ring around the tube and turn the apparatus on. This will make the ring jump into the air. Turn off the machine then, place the split ring around the pole, turn on the machine and this will not do anything. Resistive heating can be demonstrated by holding the full rings down and feeling them heat up. Next, turn off the machine, place the copper coil around the pole and press down on the copper rod sticking off the coil to create sparks. Also, place the light bulb circuit ring against the flat top part of the pole and watch it light up. Physics and Science Concepts: Lenz law, Electromagnetic Induction, Eddy Currents Safety: Do not place apparatus directly under a light. Do not stand above machine when the rings jump. Do not hold the full ring down too long, you may get burned.
PIRA Code(s): 1Q30.60 Set up time:10 minutes Operation: Spin the frame and watch the two balls move outwards. For the plexiglass demo, squirt green liquid (or pour) into the frame so that the liquid is at least an inch deep. Then, plug in the cord. Physics and Science Concepts: Centrifugal force Safety: Make sure objects and people are well clear of the spinning frame. Wear safety goggles during operation.
PIRA Code(s): 3B10.30 Set up time:none Operation: Displace the rod at one end to create a torsion pulse or wave. The other end can be left free to move, fixed in place, or critically damped. To damp the model, clip the damping cup to the last rod on one end to get an inverse reflex wave. The damping clip on the rod ends the wave entirely. Physics and Science Concepts: Torsion Waves, Waves and Oscillations Safety: None