PIRA Code(s): 1C20.10 Set up time:1 minute Operation: Tip the tube with penny and feather upside down. The penny will fall faster than the feather. Then, use the pump to evacuate all of the air. Like before, turn the tube upside down and the two objects will fall at the same rate. Physics and Science Concepts: Uniform Acceleration, Mechanics, Gravity Safety: Do not crack tube.
Must check out demonstration 3B30.30 to obtain and use pump.
PIRA Code(s): 1D60.10 Set up time:1 minute Operation: Press down on the inside of the cup. Turn the cart over, and stick the pin in the hole that protrudes from the bottom of the cart. Place the ball inside the cup. Then, push the car at a constant velocity as you gently pull the string. The ball should pop up and land in the cup again. Physics and Science Concepts: Mechanics, Motion in Two Dimensions, Projectile Motion Safety: None
PIRA Code(s): 1D60.30 Set up time:10 minutes Operation: Set up two ring stands about 8 feet apart. Put the blow gun in the clamp on one stand with the power cords to the inside of the set up. Attach the pole with the magnet to the other ring stand. Place the ball into the blow gun. Switch the power supply on which connects the circuit and then place the monkey (band aid box) on to the magnet, upside down. Make sure the blow gun is aimed directly at the broad side of the monkey. Now, blow into the blow gun to release the ball and break the circuit, thus causing the monkey to fall. The ball should hit the monkey as it falls. Physics and Science Concepts: Projectile Motion, Gravity, and Mechanics Safety: Do not turn power supply on before inserting the ball into the blow gun, due to possible electrocution.
Not all pieces (ring stand, 5 V ½ Amp DC power supply, and clamps) are in the kit, these items need to be acquired.
PIRA Code(s): 1M20.10 Set up time:none Operation: These may be used by themselves or with other demonstrations. Physics and Science Concepts: Mechanics, Mechanical Advantage, Simple Machines Safety: None
PIRA Code(s): 1M20.30 Set up time:5 minutes Operation: Set the empty friction box on the incline with weights attached to the string on the other side of the pulley so that the box slides forward. Then, gradually increase the angle of the plane until the box and the weights reach equilibrium. Physics and Science Concepts: Equilibrium of forces, Mechanics, Work and Energy Safety: None
PIRA Code(s): 1M40.10 Set up time:5 minutes Operation: Hook the bowling ball onto the chain. Pull the bowling ball back until it reaches your nose. Release the ball and do not move. Let the ball come back and show how it will not reach your nose again. *For use in lecture room 131. Physics and Science Concepts: Mechanics, Work and Energy Safety: Do not give the ball an initial velocity or move forward once the ball is release. Warning: it’s hard not to flinch.
PIRA Code(s): 1N30.10 Set up time:1 minute Operation: Pull back a number of balls and let them collide with the other balls, allowing the same number of balls to be released on the other side. Physics and Science Concepts: Conservation of linear momentum Safety: Align the balls for the best results. Do not allow the strings to tangle.
PIRA Code(s): 1Q40.30, 1Q50.24 Set up time:3 minutes Operation: Stand on the stool as it remains still. Have someone start the motor and place the bicycle wheel next to it to get it to start spinning. Take the spinning wheel in your hands and turn the wheel in a horizontal position and you should spin. When the wheel is placed vertical again, you will spin the opposite direction.
Use the motor to start the wheel spinning. Hold on to the cord attached to the axle and the wheel will remain vertical. Physics and Science Concepts: Mechanics, Rotational Dynamics Safety: Do not get items caught in the motor or the spokes of the tire. Hold wheel out from the body as far as possible
PIRA Code(s): 1Q50.30 Set up time:1 minute Operation: Rotational Dynamics, Mechanics, Gyroscopic Motion Physics and Science Concepts: Rotational Dynamics, Mechanics, Gyroscopic Motion Safety: The central gyroscope is quite heavy and can pinch fingers.
PIRA Code(s): 1Q50.60 Set up time:2 minutes Operation: Use the string or turn the rotor with your thumb to start the gyroscope spinning. Take care to hold the gyroscope and metal hold in place relative to the top block of wood. Then, spin the wooden block, stop it, and reverse the direction of the spin. The gyroscope will do a spin flip. Physics and Science Concepts: Rotational dynamics, Mechanics Safety: None
PIRA Code(s): 2B30.30 Set up time:3 minutes Operation: Place the two halves together. Put the vacuum pump on the valve and evacuate the air inside. Try to separate the pieces. Vacuum pump not included; it must be obtained from demo 3B30.30. Physics and Science Concepts: Fluid Mechanics, Statics of Fluids Safety: None
PIRA Code(s): 3B30.30 Set up time:10 minutes (5 minutes to pump the bell jar) Operation: Plug in the pump and attach the clear tube of the pump to the valve. Turn the switch on the power supply to ascertain that the alarm is working properly. Then, pump out the air inside the bell jar. It will take about 5 minutes to obtain a low enough air pressure so that the alarm will not sound. Turn the alarm on and slowly open the valve, allowing the air pressure in the bell jar to increase. The sound of the alarm will also gradually increase. Physics and Science Concepts: Sound waves Safety: A glass jar containing a vacuum can be extremely hazardous if broken.
PIRA Code(s): 5A50.10 Set up time:2 minutes Operation: Place the four (two large, two small) balls on the poles in the front about 1 inch apart. Turn the crank. Physics and Science Concepts: Electrostatics Safety: Do not touch any metal portions of the generator
PIRA Code(s): 5A50.30 Set up time:10 minutes Operation: Plug in the generator. Turn on the rocker switch and adjust speed using potentiometer on the base of the Van de Graaff.
Other suggested uses include combining this with other electrostatic demonstrations found under a 5A50 heading. Also, throwing packing peanuts or taping strips of paper to the Van de Graaff are popular demonstrations. Physics and Science Concepts: Static Electricity, Friction Safety: The rod works best on dry days with the blue wig. Care should be taken when operating. Do not approach the generator while it is running. Use the grounding rod to discharge.
PIRA Code(s): 5H10.30 Set up time:3 minutes Operation: Place the magnet under the piece of paper and on the overhead. Sprinkle iron filings over the magnet and the filings should align with the magnetic field. Physics and Science Concepts: Magnetic Fields and Forces Safety: An overhead can be obtained from demonstration 9A36.10.
PIRA Code(s): 5H30.10 Set up time:2 minutes Operation: Plug in the cathode ray tube. Deflect the beam of the CRT by holding a permanent magnet near the edge of the tube. If the beam disappears, you are holding the magnet too close. Also, you can deflect the beam by attaching a battery to the binding posts and adjusting the variable control knob. Physics and Science Concepts: Magnetic Fields and Forces Safety: None
PIRA Code(s): 5K20.10 Set up time:5 minutes Operation: Set up the pole with the right angle clamp and pendulum. Place the permanent magnet so that the copper sheet is in between the two magnet sides. Swing the full copper sheet swing through the magnet. Watch as it damps out quickly. The, flip the pendulum so that the copper comb side is swinging through the magnet. Watch how it swings as if the magnet is not even there. Physics and Science Concepts: Electromagnetic Induction, Eddy Currents Safety: Stand to the side of the pendulum as it swings, not directly in the path.
PIRA Code(s): 5K20.30 Set up time:2 minutes Operation: Set up the apparatus so that the silver pole sticks above the platform a few inches. Place a full ring around the tube and turn the apparatus on. This will make the ring jump into the air. Turn off the machine then, place the split ring around the pole, turn on the machine and this will not do anything. Resistive heating can be demonstrated by holding the full rings down and feeling them heat up. Next, turn off the machine, place the copper coil around the pole and press down on the copper rod sticking off the coil to create sparks. Also, place the light bulb circuit ring against the flat top part of the pole and watch it light up. Physics and Science Concepts: Lenz law, Electromagnetic Induction, Eddy Currents Safety: Do not place apparatus directly under a light. Do not stand above machine when the rings jump. Do not hold the full ring down too long, you may get burned.
PIRA Code(s): 3B10.30 Set up time:none Operation: Displace the rod at one end to create a torsion pulse or wave. The other end can be left free to move, fixed in place, or critically damped. To damp the model, clip the damping cup to the last rod on one end to get an inverse reflex wave. The damping clip on the rod ends the wave entirely. Physics and Science Concepts: Torsion Waves, Waves and Oscillations Safety: None