PIRA Code(s): 1D15.45 Set up time:1 minute Operation: Place balls of equal mass and size at the top of the tracks, one at the cycloid, one at the parabola, and one at the straight track. Let the balls roll down, the cycloid ball will arrive first. Then, place two balls on the cycloid track, one at the top and one a little ways down. The two balls will reach the end at the same time. Physics and Science Concepts: Motion in Two Dimensions Safety: None
PIRA Code(s): 1D60.30 Set up time:10 minutes Operation: Set up two ring stands about 8 feet apart. Put the blow gun in the clamp on one stand with the power cords to the inside of the set up. Attach the pole with the magnet to the other ring stand. Place the ball into the blow gun. Switch the power supply on which connects the circuit and then place the monkey (band aid box) on to the magnet, upside down. Make sure the blow gun is aimed directly at the broad side of the monkey. Now, blow into the blow gun to release the ball and break the circuit, thus causing the monkey to fall. The ball should hit the monkey as it falls. Physics and Science Concepts: Projectile Motion, Gravity, and Mechanics Safety: Do not turn power supply on before inserting the ball into the blow gun, due to possible electrocution.
Not all pieces (ring stand, 5 V ½ Amp DC power supply, and clamps) are in the kit, these items need to be acquired.
PIRA Code(s): 1G20.45 Set up time:2 minutes Operation: Hold a slinky in your hand high enough so that when it falls it will not touch the floor. Still holding the top of the slinky, let the rest drop down towards the ground. Physics and Science Concepts: Newton’s Second Law Safety: Ends of slinky may be sharp or become tangled
PIRA Code(s): 1M20.30 Set up time:5 minutes Operation: Set the empty friction box on the incline with weights attached to the string on the other side of the pulley so that the box slides forward. Then, gradually increase the angle of the plane until the box and the weights reach equilibrium. Physics and Science Concepts: Equilibrium of forces, Mechanics, Work and Energy Safety: None
PIRA Code(s): 1Q40.30, 1Q50.24 Set up time:3 minutes Operation: Stand on the stool as it remains still. Have someone start the motor and place the bicycle wheel next to it to get it to start spinning. Take the spinning wheel in your hands and turn the wheel in a horizontal position and you should spin. When the wheel is placed vertical again, you will spin the opposite direction.
Use the motor to start the wheel spinning. Hold on to the cord attached to the axle and the wheel will remain vertical. Physics and Science Concepts: Mechanics, Rotational Dynamics Safety: Do not get items caught in the motor or the spokes of the tire. Hold wheel out from the body as far as possible
PIRA Code(s): 1Q50.30 Set up time:1 minute Operation: Rotational Dynamics, Mechanics, Gyroscopic Motion Physics and Science Concepts: Rotational Dynamics, Mechanics, Gyroscopic Motion Safety: The central gyroscope is quite heavy and can pinch fingers.
PIRA Code(s): 2B30.30 Set up time:3 minutes Operation: Place the two halves together. Put the vacuum pump on the valve and evacuate the air inside. Try to separate the pieces. Vacuum pump not included; it must be obtained from demo 3B30.30. Physics and Science Concepts: Fluid Mechanics, Statics of Fluids Safety: None
PIRA Code(s): 5A22.22 Set up time:3 minutes Operation: First, show the electroscope in resting stage. Then, charge a rod or other material by rubbing the object in a cloth. Place this near the plate of the electroscope and observe the deflection of the needle. To keep the needle deflected, scrape the plate with the charged object. A decrease in deflection occurs when an oppositely charged object is placed near the plate. Physics and Science Concepts: Electrostatics Safety: None
PIRA Code(s): 5A50.30 Set up time:10 minutes Operation: Plug in the generator. Turn on the rocker switch and adjust speed using potentiometer on the base of the Van de Graaff.
Other suggested uses include combining this with other electrostatic demonstrations found under a 5A50 heading. Also, throwing packing peanuts or taping strips of paper to the Van de Graaff are popular demonstrations. Physics and Science Concepts: Static Electricity, Friction Safety: The rod works best on dry days with the blue wig. Care should be taken when operating. Do not approach the generator while it is running. Use the grounding rod to discharge.
PIRA Code(s): 5F20.50 Set up time:5 minutes Operation: First, attach the metal rods to the battery by unscrewing the black caps and place the rods around the screws. Then replace the caps. Next, clip one light bulb on the metal rods to show a circuit with a single light bulb. To show series circuits, clip two bulbs together and place the end of each clip on opposite rods. To show parallel circuits, clip each bulb separately to the rods. The bulbs in series will glow less brightly than the bulbs in parallel. Physics and Science Concepts: Parallel and series circuits Safety: The ends of the rods pose an eye hazard.
PIRA Code(s): 5G50.50 Set up time:2 minutes Operation: A superconductor disc is placed in a styrofoam dish and liquid nitrogen is added to the dish. A small magnet is placed on top and within a few seconds it begins to levitate. Physics and Science Concepts: Superconductivity, Magnetic Materials Safety: Liquid Nitrogen can be obtained from the machine shop.
PIRA Code(s): 5H10.30 Set up time:3 minutes Operation: Place the magnet under the piece of paper and on the overhead. Sprinkle iron filings over the magnet and the filings should align with the magnetic field. Physics and Science Concepts: Magnetic Fields and Forces Safety: An overhead can be obtained from demonstration 9A36.10.
PIRA Code(s): 5K20.30 Set up time:2 minutes Operation: Set up the apparatus so that the silver pole sticks above the platform a few inches. Place a full ring around the tube and turn the apparatus on. This will make the ring jump into the air. Turn off the machine then, place the split ring around the pole, turn on the machine and this will not do anything. Resistive heating can be demonstrated by holding the full rings down and feeling them heat up. Next, turn off the machine, place the copper coil around the pole and press down on the copper rod sticking off the coil to create sparks. Also, place the light bulb circuit ring against the flat top part of the pole and watch it light up. Physics and Science Concepts: Lenz law, Electromagnetic Induction, Eddy Currents Safety: Do not place apparatus directly under a light. Do not stand above machine when the rings jump. Do not hold the full ring down too long, you may get burned.
PIRA Code(s): 3B10.30 Set up time:none Operation: Displace the rod at one end to create a torsion pulse or wave. The other end can be left free to move, fixed in place, or critically damped. To damp the model, clip the damping cup to the last rod on one end to get an inverse reflex wave. The damping clip on the rod ends the wave entirely. Physics and Science Concepts: Torsion Waves, Waves and Oscillations Safety: None