PIRA Code(s): 3A10.20 Set up time:1 minute Operation: Move the weight along the hacksaw blade. Pull back on the blade and release. When the weight is at the top of the blade the frequency is smaller compared to when the weight is at the bottom. Physics and Science Concepts: Oscillations Safety: Edge of blade may be sharp.
PIRA Code(s): 5A20.20 Set up time:1 minute Operation: Charge the rod by rubbing it the through the cloth provide or on your shirt. Hold the rod near a pith ball. The two balls will repel each other. The PVC gives a positive charge and the acrylic rod gives negative charge. Physics and Science Concepts: Electrostatics, Coulomb’s Law Safety: None
PIRA Code(s): 5A50.10 Set up time:2 minutes Operation: Place the four (two large, two small) balls on the poles in the front about 1 inch apart. Turn the crank. Physics and Science Concepts: Electrostatics Safety: Do not touch any metal portions of the generator
PIRA Code(s): 5B30.20 Set up time:5 minutes Operation: Use the Van der Graaf or Wimshurst generator to charge the ovoid. Touch a proof plane to the pointed end of the ovoid and another to the spherical end. Place the proof planes on the electroscope plate. The deflection will be greater from the proof plane that touched the pointed end. Physics and Science Concepts: Electrostatics, Surface Charge Density Safety: Electroscope can be obtained from demonstration number 5A22.22.
PIRA Code(s): 5C10.20 Set up time:none Operation: Charge the plates using the Van de Graaff. Disconnect wire going from top of sphere to fixed plate at plate end. Change the spacing of a charged parallel plate capacitor while it is attached to an electroscope. Observe changes in electroscope pointer. Physics and Science Concepts: Capacitance Safety: Electroscope can be obtained from demo 5A22.22. The Van de Graaff can be obtained from demo 5A50.30.
PIRA Code(s): 5E40.20 Set up time:1 minute Operation: Pour sulfuric acid into the glass container. Wait 5 minutes for the reaction to take place between the dissimilar metals. Place the voltmeter on the overhead and display the voltage generated in the cell. Physics and Science Concepts: Electromotive Force and Current Safety: Be careful around acid. Gloves and goggles should be worn when handling acid.
PIRA Code(s): 5H30.10 Set up time:2 minutes Operation: Plug in the cathode ray tube. Deflect the beam of the CRT by holding a permanent magnet near the edge of the tube. If the beam disappears, you are holding the magnet too close. Also, you can deflect the beam by attaching a battery to the binding posts and adjusting the variable control knob. Physics and Science Concepts: Magnetic Fields and Forces Safety: None
PIRA Code(s): 5K10.20 Set up time:1 minute Operation: Hook the leads from the galvanometer to the induction coil. Place a magnet in front of the coil. Turn the crank and the needle on the galvanometer should move. The connection between the galvanometer and the loop changes polarity every half turn. Physics and Science Concepts: Electromagnetic Induction, Electricity and Magnetism Safety: Magnet is extremely strong so do not place metal objects near it.
PIRA Code(s): 5K20.10 Set up time:5 minutes Operation: Set up the pole with the right angle clamp and pendulum. Place the permanent magnet so that the copper sheet is in between the two magnet sides. Swing the full copper sheet swing through the magnet. Watch as it damps out quickly. The, flip the pendulum so that the copper comb side is swinging through the magnet. Watch how it swings as if the magnet is not even there. Physics and Science Concepts: Electromagnetic Induction, Eddy Currents Safety: Stand to the side of the pendulum as it swings, not directly in the path.
PIRA Code(s): 5K20.30 Set up time:2 minutes Operation: Set up the apparatus so that the silver pole sticks above the platform a few inches. Place a full ring around the tube and turn the apparatus on. This will make the ring jump into the air. Turn off the machine then, place the split ring around the pole, turn on the machine and this will not do anything. Resistive heating can be demonstrated by holding the full rings down and feeling them heat up. Next, turn off the machine, place the copper coil around the pole and press down on the copper rod sticking off the coil to create sparks. Also, place the light bulb circuit ring against the flat top part of the pole and watch it light up. Physics and Science Concepts: Lenz law, Electromagnetic Induction, Eddy Currents Safety: Do not place apparatus directly under a light. Do not stand above machine when the rings jump. Do not hold the full ring down too long, you may get burned.